Little Bear Westsail 32 refit: Bowsprit Platform Prep Blog #131

Arrrrr me hearties. Welcome aboard.

After leaving everyone hanging in regards to how I expanded the thru-hull hole, I reveal the mystery of how I did it. A simple enough tactic and it worked very well.

The next project is to get the bowsprit platform mounted on the bowsprit. Without the platform, sail management at the front of the boat would be a very scary proposition. So, the platform must be reinstalled. The teak for the platform was in very rough shape when I took it off. Previous episodes show how I repaired & restored the wood. I’m glad I put the effort into restoring it. Teak is beautiful wood and holds up well in the maritime environment.

The first thing I did was to epoxy the G10 brackets I made into place. They are probably a bit redundant as they are an addition to the sprit that wasn’t there when I bought the boat. But considering that the platform is fairly thin compared to what the plans call for, I feel better having them in place. Stronger is better, in this case.

The sail maker came by while I wasn’t here to measure the boat for sails. This may prove to be an issue later on.

As always fair winds, following seas, and God bless.

Little Bear Westsail 32 refit: Sail Loft Blog #130

Arrrrr me hearties. Welcome aboard.

This episode is the documentation of a trip to the sail loft. Some months ago I contacted about three different lofts asking for quotes for the boat. I asked a high-end loft, North Sails, and a lower end, budget loft for quotes. As I expected, the high-end quote was out of my price-range. Mind you, you get what you pay for and what they offered was definitely in the excellent category. The low end just seemed too sketchy so I decided to go with North Sails. They’ve been around a long time, are a global company and have a good reputation.

So, in this vid, I take my sails into the NS loft for an assessment.

The consultant was reluctant to say any of my sails were junk but I decided to buy new genoa (130%), inner jib / stays’l, and main. It was an interesting visit to be sure.

As always fair winds, following seas, and God bless.

Little Bear Westsail 32 refit: Out with the old! Blog #129

Arrrrr me hearties. Welcome aboard.

This post should have come before the previous post but in a fit of air-headedness, I got them reversed. Ces’t la vie.

I got the old zinc’s off, and I took out the old speed-log through Hull. I tried to remove the thru-hull elegantly and properly but it proved to difficult for culture and class. So, I resorted to a small sledge and smashed it out. 😀 When all else fails, get a bigger hammer.

As always fair winds, following seas, and God bless.

Little Bear Westsail 32 refit: Of Zinc & Holes Blog #128

Arrrrr me hearties. Welcome aboard.

With the major projects on Little Bear winding up, I have a minor project to get done: New Zinc’s. Not much mystery surrounding this project – take the old ones off, put the new ones back on. All shiny and clean.

This is what the old ones looked like.

I’m no expert on electrolytic or galvanic corrosion but these zincs look pretty bad. I have NO idea when they were replaced last, but I’m glad the prop & shaft and other bits of metal in the boat aren’t adversely affected.

The other smallish project I’m tackling is the installation of my ‘tri-ducer’. The challenge with this is that the new thru-hull is larger than the current hole in the boat. Which means I have to employ my genius super-power and figure out how to enlarge the existing hole. How will I do it? Ah, grasshopper, when you are ready the solution will come….

As always fair winds, following seas, and God bless.

Little Bear Westsail 32 refit: Copper Coat Sanding Blog #135

Arrrrr me hearties. Welcome aboard.

Months and months ago I decided on using coppercoat to treat the bottom of Little Bear. The keel is relatively deep at 5′ and long. Cleaning that much underwater real-estate doesn’t really turn my crank so the best solution I could come up with was coppercoat.

While coppercoat is expensive up front the long term savings make this choice a sound financial decision.

In this episode I have to sand the coppercoat in order to expose the copper. This is a necessary  step because it’s not the copper that stops marine growth but the oxide that is created when copper reacts with salt water. If the copper isn’t exposed, it won’t react, and it won’t oxide, meaning that it won’t have any repellant properties.

While I consider myself to be a fairly creative chap, I was really at a loss on how to make a sanding-the-bottom video interesting. I also found this project to be physically painful and demanding. The reason being that I had to assume an awkward position with the sander for an extended amount of time. Well, enough whinging, let’s get on with it…

As always fair winds, following seas, and God bless.

Little Bear Westsail 32 refit: Le Boom! Vlog #126

Arrrrr me hearties. Welcome aboard.

The mast is up but it has no boom! Fortunately the boom is a much smaller bit of hardware, one which can be easily handled by one old pirate.

I started by stripping it, cleaning the stainless, sanding, sanding, yet more sanding, priming, painting, and then reinstalling the hardware. I ran into the same stainless / aluminium corrosion issue that I found on the mast. I had to make time to buy bits and pieces so that I was prepared with Helicoils and other requisite stuff. I used Locktite Blue to provide a barrier between the stainless screws & bolts and the aluminum boom. The riggers advised me to use a product called ‘Lanocote’ and I ordered some but it didn’t arrive till after I had everything assembled already.

Experience is a wonderful thing. If I were to refit another boat I would know what tools and products I would likely need so I could order them beforehand. This would make projects MUCH shorter in terms of time. I have wasted a LOT of time waiting for things to be ordered / arrive. I suppose this also explains why taking things apart is so much faster than putting them back together.

As always fair winds, following seas, and God bless.

Little Bear Westsail 32 refit: The Stick goes up! Vlog #125

Arrrrr me hearties. Welcome aboard.

Today is the long anticipated day – the mast goes back up today. What a huge milestone. There was much stokage, and much excitement on this day; let me tell you! Steve Wight Rigging was the chap who got the job of putting the mast back up. He also did all the rigging and repaired the roller furler foils. The roller furler foils got bent when I took the mast off. It took 3 months to order and have the new foil sections delivered but that’s just as well because I wasn’t ready with the mast anyway. Metro Cranes provided the lift and the day went off without a hitch. All the work and prep done prior to installation day paid off.

Next project: the boom. Stay tuned.

As always fair winds, following seas, and God bless.